鋁合金模板廠家加固及校正  

1. 墻模板的加固處理  墻模板安裝完畢后，在模板上預留孔穿上對拉螺桿，布置上、中、下共三道。對拉螺桿外邊附三道背楞，轉角處設置直角背楞，防止墻模板發生扭轉、錯臺，保證結構的順直光滑。安裝背楞及穿墻螺桿應兩人在墻柱的兩側同時進行，背楞及穿墻螺桿安裝緊固牢靠，不能過緊或過松。  

2. 
   

2.墻柱實測實量的校正  墻模板安裝完畢后，安裝斜向支撐，對墻模板的水平標高及垂直度作初步調整。用掛線錘或用激光掃平儀檢查墻柱的垂直度，并進行校正，在墻柱兩側的對應部位加頂斜支撐，斜支撐間距不大于2000mm，寬度大于2000mm的墻體須設置不少于兩根斜撐，寬度小于1200mm的墻體或剪力墻體不少于一根斜撐，外墻無法設置斜支撐時可用手拉葫蘆和斜支撐做到一拉一頂，斜支撐一端固定在背楞上，另一端用膨脹螺栓固定在樓板上，以保證墻柱垂直度在澆筑混凝土時不會偏移，墻柱垂直度偏差應控制在5mm內。  

3.頂板實測實量的校正    根據樓層標高，用紅外線先檢查梁底是否水平，河北鋁合金模板廠家調節可調節支撐桿至梁底水平，再用紅外線檢查頂板的水平差，調節頂板的每一根支撐桿，直至頂板水平差符合要求。同一跨內頂板水平差應控制在5mm范圍內。